konica minolta bizhub C258/ C368 motor arıza develop ineo 258 368 arızası için 05322603702 

konica bizhub C258/ C368 motor arızası

bizhub C258/ C368 motor

develop ineo 258 motor 

develop 258 motor fiyatı

2.el C258/ C368 motor 

konica bizhub C258/ C368 develop 

Code: C1112

Description: Stapler motor malfunction (When FS-534SD is installed) • The stapler home sensor is not turned ON even after the set period of time has elapsed while the stapler motor is energized. • The stapler home sensor is not turned OFF even after the set period of time has elapsed after the stapler home sensor is turned ON.

Causes: • Staple unit • SD drive board (SDDB) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between the staple unit-SDDB J4 for proper connection and correct as necessary. 2. Check the connector of the staple unit for proper drive coupling and correct as necessary. 3. Replace the staple unit. 4. Replace SDDB. 5. Replace FSCB.

Code: C1113

Description: Center-staple lead edge stopper motor malfunction (When FS-534SD is installed) The stopper home sensor (PS6) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the stopper drive motor (M4) is turned ON.

Causes: • Stopper drive motor (M4) • Stopper home sensor (PS6) • SD drive board (SDDB) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M4-SDDB J10 for proper connection and correct as necessary. 2. Check the connector of M4 for proper drive coupling and correct as necessary. 3. Check the connector between PS6-SDDB J10 for proper connection and correct as necessary. 4. PS6 I/O check, sensor check • Control signal: SDDB J10-5 (ON) • Location of electrical component: SD-511 2-G 5. M4 operation check • Control signal: SDDB J10-6 to 9 • Location of electrical component: SD-511 1 to 2-F to G 6. Replace M4. 7. Replace SDDB. 8. Replace FSCB.

Code: C1114

Description: Center-staple front adjust drive motor malfunction (When FS-534SD is installed) The alignment home sensor (PS4) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the alignment motor (M3) is turned ON.

Causes: • Alignment motor (M3) • Alignment home sensor (PS4) • SD drive board (SDDB) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M3-relay CN10-SDDB J7 for proper connection and correct as necessary. 2. Check the connector of M3 for proper drive coupling and correct as necessary. 3. Check the connector between PS4-relay CN10-SDDB J7 for proper connection and correct as necessary. 4. PS4 I/O check, sensor check • Control signal: SDDB J7-6 (ON) • Location of electrical component: SD-511 6-F 5. M3 operation check • Control signal: SDDB J7-7 to 10 • Location of electrical component: SD-511 5-F to G 6. Replace M3. 7. Replace SDDB. 8. Replace FSCB.

Code: C1115

Description: Center-staple knife drive motor malfunction (When FS-534SD is installed) The center fold knife home sensor (PS8) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON.

Causes: • Center fold knife motor (M9) • Center fold knife home sensor (PS8) • SD drive board (SDDB) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M9-SDDB J11 for proper connection and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS8-relay CN10-SDDB J7 for proper connection and correct as necessary. 4. PS8 I/O check, sensor check • Control signal: SDDB J7-3 (ON) • Location of electrical component: SD-511 6-G 5. M9 operation check • Control signal: SDDB J11-11 to 20 • Location of electrical component: SD-511 1 to 2-B 6. Replace M9. 7. Replace SDDB. 8. Replace FSCB.

Code: C1132

Description: Punch drive motor malfunction (When FS-533+PK-519, FS-534+PK-520 or FS-534SD+PK-520 is installed) <When FS-533+PK-519 is installed> • The puncher drive cam sensor (PS203) or puncher home sensor (PS204) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch motor (M201) is energized. • The punch motor sensor (PS202) is not turned ON when the punch motor (M201) driven. • The holes with other marketing area is set in [Service Mode] -> [Finisher] -> [Punch Option Setting]. <When FS-534+PK-520 or FS-534SD+PK-520 is installed> • The punch home sensor (PS1) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the punch drive motor (M1) is energized. • Thick paper is loaded and a punch operation is performed with [Plain Paper] left set for the paper type.

Causes: <When FS-533+PK-519 is installed> • Punch motor (M201) • Punch motor sensor (PS202) • Puncher drive cam sensor (PS203) • Puncher home sensor (PS204) • PK control board (PKCB) • FS control board (FSCB) <When FS-534+PK-520 or FS-534SD+PK-520 is installed> • Punch drive motor (M1) • Punch home sensor (PS1) • FS control board (FSCB)

Troubleshooting Guides: When FS-533+PK-519 is installed 1. Check the number of the holes in [Service Mode] -> [Finisher] -> [Punch Option Setting]. 2. Check the connector between M201-PKCB CN203 for proper connection and correct as necessary. 3. Check the connector of M201 for proper drive coupling and correct as necessary. 4. Check the connector between PS202-PKCB CN204 for proper connection and correct as necessary. 5. Check the connector between PS203-PKCB CN204 for proper connection and correct as necessary. 6. Check the connector between PS204-PKCB CN204 for proper connection and correct as necessary. 7. PS202 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 5-C 8. PS203 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 6-C 9. PS204 I/O check, sensor check • Control signal: PKCB CN204 • Location of electrical component: FS-533 (PK-519) 6-C 10. M201 operation check • Control signal: PKCB CN203-1 to 2 • Location of electrical component: FS-533 (PK-519) 4-C 11. Replace M201. 12. PKCB F201 conduction check 13. Replace PKCB. 14. Replace FSCB. When FS-534+PK-520 or FS-534SD+PK-520 is installed 1. Check that the correct paper type is set. To print on thick paper, change the paper type to [Thick]. 2. If the trouble occurs even when [Paper Type] is set to the correct paper type, select [Service Mode] -> [Security Settings] -> [Engine FW DipSW] and flip SW No. 17 to the ON. NOTE • Changing the setting of Engine FW DipSW results in a longer perforating time and greater punch perforating noise regardless of the paper type. 3. Check the connector between M1-relay CN351-FSCB J7 for proper connection and correct as necessary. 4. Check the connector of M1 for proper drive coupling and correct as necessary. 5. Check the connector between PS1-FSCB J7 for proper connection and correct as necessary. 6. PS1 I/O check, sensor check • Control signal: FSCB J7-5 (ON) • Location of electrical component: FS-534 (PK-520) 7-K 7. M1 operation check • Control signal: FSCB J7-7 to 8 • Location of electrical component: FS-534 (PK-520) 7-K 8. Replace M1. 9. Replace FSCB.

Code: C1140

Description: Alignment plate motor/Rr malfunction (When FS-533, FS-534 or FS-534SD is installed) <When FS-533 is installed> • The alignment plate home sensor/R (PS109) is not turned OFF (unblocked) after the set period of time has elapsed after the plate drive starts from the home position. • The alignment plate home sensor/R (PS109) is not turned ON (blocked) after the set period of time has elapsed while the alignment motor/R (M106) is energized when the plate returns to the home position. <When FS-534 or FS-534SD is installed> • The alignment plate/R home sensor (PS13) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the alignment motor/Rear (M8) is energized.

Causes: <When FS-533 is installed> • Alignment motor/R (M106) • Alignment plate home sensor/R (PS109) • FS control board (FSCB) <When FS-534 or FS-534SD is installed> • Alignment motor/Rear (M8) • Alignment plate/R home sensor (PS13) • FS control board (FSCB)

Troubleshooting Guides: When FS-533 is installed 1. Check the connector between M106-FSCB CN102 for proper connection and correct as necessary. 2. Check the connector of M106 for proper drive coupling and correct as necessary. 3. Check the connector between PS109-FSCB CN102 for proper connection and correct as necessary. 4. PS109 I/O check, sensor check • Control signal: FSCB CN102 • Location of electrical component: FS-533 7-J 5. M106 operation check • Control signal: FSCB CN102 • Location of electrical component: FS-533 8-J 6. Replace M106 7. FSCB CP105 conduction check 8. Replace FSCB When FS-534 or FS-534SD is installed 1. Check the connector between M8-FSCB J12 for proper connection and correct as necessary. 2. Check the connector of M8 for proper drive coupling and correct as necessary. 3. Check the connector between PS13-FSCB J9 for proper connection and correct as necessary. 4. PS13 I/O check, sensor check • Control signal: FSCB J9<B>-9 (ON) • Location of electrical component: FS-534 9-C 5. M8 operation check • Control signal: FSCB J12-13 to 16 • Location of electrical component: FS-534 5 to 6-C to D 6. Replace M8. 7. Replace FSCB.

Code: C1141

Description: Paddle motor drive malfunction (When FS-534 or FS-534SD is installed) The upper paddle home position detection sensor (PS14) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the FNS paddle motor (M5) is turning.

Causes: • FNS paddle motor (M5) • Upper paddle home position detection sensor (PS14) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M5-FSCB J4 for proper connection and correct as necessary. 2. Check the connector of M5 for proper drive coupling and correct as necessary. 3. Check the connector between PS14-FSCB J4 for proper connection and correct as necessary. 4. PS14 I/O check, sensor check • Control signal: FSCB J4<B>-7 (ON) • Location of electrical component: FS-534 13-C 5. M5 operation check • Control signal: FSCB J4<A>-9 to 12 • Location of electrical component: FS-534 12-C to D 6. Replace M5. 7. Replace FSCB.

Code: C1144

Description: Pre-eject drive motor malfunction (When FS-534 or FS-534SD is installed) • The pre-eject home sensor (PS21) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON. • The pre-eject away sensor (PS22) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the pre-eject drive motor (M9) is turned ON.

Causes: • Pre-eject drive motor (M9) • Pre-eject home sensor (PS21) • Pre-eject away sensor (PS22) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M9-relay CN7<A>-FSCB J13 for proper connection, and correct as necessary. 2. Check the connector of M9 for proper drive coupling and correct as necessary. 3. Check the connector between PS21-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 4. Check the connector between PS22-relay CN8-relay CN7<B>-FSCB J12 for proper connection, and correct as necessary. 5. PS21 I/O check, sensor check • Control signal: FSCB J12-6 (ON) • Location of electrical component: FS-534 6-C 6. PS22 I/O check, sensor check • Control signal: FSCB J12-9 (ON) • Location of electrical component: FS-534 6-C 7. M9 operation check • Control signal: FSCB J13-3 to 4 • Location of electrical component: FS-534 8-C to D 8. Replace M9. 9. Replace FSCB.

Code: C1145

Description: Trailing edge stopper motor malfunction (When FS-534 or FS-534SD is installed) The trailing edge stopper home position detection sensor (PS20) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the trailing edge stopper motor (M6) is turned ON.

Causes: • Trailing edge stopper motor (M6) • Trailing edge stopper home position detection sensor (PS20) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M6-FSCB J5 for proper connection and correct as necessary. 2. Check the connector of M6 for proper drive coupling and correct as necessary. 3. Check the connector between PS20-relay CN22-FSCB J5 for proper connection and correct as necessary. 4. PS20 I/O check, sensor check • Control signal: FSCB J5-9 (ON) • Location of electrical component: FS-534 9-K 5. M6 operation check • Control signal: FSCB J5-13 to 16 • Location of electrical component: FS-534 9-K 6. Replace M6. 7. Replace FSCB.

Code: C1156

Description: SD paddle motor malfunction (When FS-534SD is installed) The paddle home sensor (PS5) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the SD paddle motor (M7) is energized.

Causes: • SD paddle motor (M7) • Paddle home sensor (PS5) • SD drive board (SDDB) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M7-SDDB J8 for proper connection and correct as necessary. 2. Check the connector of M7 for proper drive coupling and correct as necessary. 3. Check the connector between PS5-SDDB J8 for proper connection and correct as necessary. 4. PS5 I/O check, sensor check • Control signal: SDDB J8-3 (ON) • Location of electrical component: SD-511 3 to 4-G 5. M7 operation check • Control signal: SDDB J8-4 to 7 • Location of electrical component: SD-511 3-F to G 6. Replace M7. 7. Replace SDDB. 8. Replace FSCB.

Code: C1182

Description: Shift motor drive malfunction (When JS-506 is installed) • The tray shift home sensor (PS1) is not turned ON (blocked) after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the home position.) • The tray shift home sensor (PS1) is not turned OFF (unblocked) after the set period of time has elapsed after the tray shift motor (M1) is turned ON (start of moving to the shift position.)

Causes: • Tray shift motor (M1) • Tray shift home sensor (PS1) • JS control board (JSCB)

Troubleshooting Guides: 1. Check the connector between M1-JSCB CN208 for proper connection and correct as necessary. 2. Check the connector of M1 for proper drive coupling and correct as necessary. 3. Check the connector between PS1-JSCB CN208 for proper connection and correct as necessary. 4. PS1 I/O check, sensor check • Control signal: JSCB CN208-5 (ON) • Location of electrical component: JS-506 5-C 5. M1 operation check • Control signal: JSCB CN208-1 (DRV) • Location of electrical component: JS-506 4 to 5-C 6. Replace M1. 7. JSCB ICP3 conduction check 8. Replace JSCB.

Code: C1184

Description: Paper discharge control motor malfunction (When FS-534 or FS-534SD is installed) The paper delivery control sensor (PS28) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed while the paper receiving control motor (M12) is energized.

Causes: • Paper receiving control motor (M12) • Paper delivery control sensor (PS28) • FS control board (FSCB)

Troubleshooting Guides: 1. Check the connector between M12-relay CN1-FRCB J14 for proper connection and correct as necessary. 2. Check the connector of M12 for proper drive coupling and correct as necessary. 3. Check the connector between PS28-relay CN1-FRCB J14 for proper connection and correct as necessary. 4. PS28 I/O check, sensor check • Control signal: FSCB J14<B>-3 (ON) • Location of electrical component: FS-534 2 to 3-C 5. M12 operation check • Control signal: FSCB J14<A>-9 to 12 • Location of electrical component: FS-534 2-C to D 6. Replace M12. 7. Replace FSCB.